Seat Belt Main Index Page Contact Us:EMail Call Us:(302) 629-8508
Single retractor and dual retractor automatic locking retractable pallet straps for industrial and commercial applications. The retractors are covered with a hard plastic boot to protect the internal components from dust, dirt and damage. Specialty mounting brackets are also listed to be used to adjust the mounting location to accomodate most installation requirements.Contact us for quantity pricing.

Single Retractor

Quantity

Add (2-MH8-3)Zinc Chromate Bolts With Lock Washers $3.30set


Click on picture to enlarge

Part Numbers
  • W8252B 57" Extended Length With Black Webbing $47.00ea
  • W8252X 57" Extended Length With Orange Webbing $47.00ea
  • W8253B 69" Extended Length With Black Webbing $49.00ea
  • Mounting Bolts 2-MH1 $2.00st
    Product Notes
  • Available in extended lengths of 57" and 69" with black or orange 1 15/16th wide webbing.
  • Buckle has metal underside with plastic cap with red press background with white "PRESS".
  • Buckle base has 1" long mounting bracket with 1/2" hole.
  • Includes black retractor cover measuring 3"L x 3 1/2"W x 2 1/2"H with a 1" webbing exit sleeeve.
  • The retractor is (ALR) automatic locking.
  • Retractor locks in place when webbing pulled and released. Must go back to retractor to pull again.
  • The retractor base bracket extends 1" from retractor and has a 9/16th mounting hole.
  • See specialty brackets for relocation of the mounting location.
  • All measurements are approximate.

  • Dual Retractor

    Quantity

    Add (2 MH8-3)Zinc Chromate Bolts With Lock Washers $3.30set


    Click on picture to enlarge

    Part Numbers
  • W8427B Dual Retractor With Black Webbing $49.00ea
  • Zinc chromate Mounting Bolts With Lock Washers 2-MH8-3 $3.30st
    Product Notes
  • Webbing width 1 15/16th. Extends 57" out from each retractor.
  • Buckle has metal underside with plastic cap with globe logo on press area.
  • A 1" long mounting bracket with 1/2" hole extends from buckle base.
  • Includes black retractor covers measuring 3"L x 3 1/2"W x 2 1/4"H with a 3/4" webbing exit sleeve.
  • The retractor is (ALR) automatic locking.
  • Retractor locks in place when webbing pulled and released. Must go back to retractor to pull again.
  • The retractor base bracket extends 1" from retractor and has a 9/16th mounting hole.
  • See specialty brackets for relocation of the mounting location.
  • All measurements are approximate.

  • Specialty Mounting Brackets

    Quantity:


    Product Notes
  • Click on picture to enlarge
  • RB6: 1 1/2" long L-bracket.Yellow Zinc.
  • RB2: 2" long L-bracket.Yellow Zinc.
  • RB9: 5" long double angle bracket.Yellow Zinc.
  • RB8: 7" long angle bracket.Yellow Zinc.
  • RB7: 3" long flat extension.Yellow Zinc.
  • RB11: 6" long flat extension.Yellow Zinc.
  • RB10: 12" long angle bracket.Yellow Zinc.
  • All measurements are approximate.


  • Liability Disclaimer: The Andover Companies, and its subsidiaries assumes no responsibility for any damage due to the installation, either proper or improper, or for any damage or bodily injury arising from the use of any product. It is understood that the purchaser, installer and/or end user is responsible for the determination that the product purchased is suitable for its intended use and agrees to indemnify and hold The Andover Companies,Inc and its subsidiaries, harmless for any claim, action or demand arising from the installation and/or use of any product. There are no guarantees or warrantees on any product, implied or expressed, of fitness for a particular use with any such warrantees being specifically and expressly disclaimed. In the event any of the above limitations are held not enforceable our liability shall not exceed an amount equal to the amount paid to us for the product. Receipt of product or products confirm acceptance of disclaimer and liability transfer to purchaser, installer and/or end user.

    All information detailed within this document is based on information believed to be accurate but accuracy is not guaranteed. All pictures, diagrams and item descriptions are protected property of The Andover Companies,Inc and are not to be duplicated in any manner without written permission.

    (pallet 2-25-13)