Seat Belts:
Late Model Replacement Style

The seat belts detailed within this section have been manufactured using a web sensitive type retractor which will allow movement within the vehicle but will lock on a pre-designed movement and have been designed to duplicate the mounting configuration where the retractor is surface mounted to or behind an interior trim panel with the shoulder harness webbing feed through bracket mounted above the retractor on the same interior trim panel which is the mounting positions used on most late model applications.This type installation also had the shoulder harness anchor end attached either on the floor near the retractor or attached to the same mounting point as the retractor.The overall length of the belts listed below is approximately 136" with approximately 57" that remains outside of the retractor when the belt is fully retracted.Will not work in Corvettes.

The plastic retractor cover,buckle,buckle end cover and shoulder harness bolt cover are color matched to the webbing color except for the red belts,where these pieces are black.WS300R mounting kits includes the required bolts,washers,lock washers and L-bracket to install one retractable lap seat belt with shouldere harness.An additional WSRB2 L-bracket may be required for buckle end mounting in the event that the buckle end is mounted to the floor rather than a transmission tunnel.


If replacing a seat belt that utilized a top release pushbutton buckle,these belts are only available as a set which includes a 12" hard plastic sleeved buckle end due to the configuration of the latch tongue.For those applications using a side release pushbutton buckle,the buckle end is not included in the set and a selection of the length and with or without a hard plastic sleeve must be made to complete the set.

Plastic covers for direct anchor belts are available in black,medium blue,burgundy,medium gray and tan for $10.00ea that snap over the anchor end bolt and cover the bolt head and anchor end for a finished look.Part number WSC10.Specify color when ordering.

To Order:
  • Call:410-381-6700 8-5 EST Monday-Friday
  • or use the secure Late Model On-Line Order Form


    • Webbing Color Samples:

    Are available for .50 per sample and can be ordered On-Line or by calling (410)381-6700 and by mail.When ordering by phone or mail please supply belt part number.Mail in orders should include payment and a self addressed postage paid envelope.
    Mail To:
    Andover Automotive,Inc
    P.O. Box 2651WS
    Columbia,Maryland 21045



    Replacement style seat belts may not be applicable to all applications.Refer to the How To Install section to see how and where they are designed to mount.Due to color variations webbing colors are not guaranteed to match original interior colors.For assistance call (410)381-6700.The actual invoice may reflect a different part number.The buckle ends are matched to the belts listed and should not be used to complete or replace a component on a set other than those listed.

    Late Model On-Line Order Form

    Column-Description                                              Cost
A-Lap/Shoulder Harness Set w/12" Top Release Pushbutton        $70.00ea
B-Lap/Shoulder Harness Select Buckle From Below To Complete    $60.00ea
C-9" Buckle End w/Removable Hard Plastic Sleeve                $12.00ea 
D-12" Buckle End w/Removable Hard Plastic Sleeve               $15.00ea
E-18" Buckle End,Non-Sleeved                                   $10.00ea
F-25" Buckle End,Non-Sleeved                                   $10.00ea
G-33" Buckle End,Non-Sleeved                                   $10.00ea
WS300R Lap/Shoulder Harness Mounting Kit/Per Belt                5.00ea
WSRB2 L-Bracket                                                 $2.50ea
WSRB1 Underbody Reinforcement Plate                            $25.00pr
WSRB3 Shoulder Harness Reinforcement Plate                     $12.00ea
    Note:The 9" buckle ends are only available in black. 
                                            Select Buckle End To Complete WS18 Set  
Color                  A        B        C        D        E        F        G
Black                WS17B    WS18B    WS95B    WS99B    WS98B    WS96B    WS97B
Medium Blue          WS17C    WS18C    WS95B    WS99C    WS98C    WS96C    WS97C
Burgundy/Maroon      WS17D    WS18D    WS95B    WS99D    WS98D    WS96D    WS97D
Medium Gray          WS17E    WS18E    WS95B    WS99E    WS98E    WS96E    WS97E
Tan                  WS17F    WS18F    WS95B    WS99F    WS98F    WS96F    WS97F
Bright Red           WS17G    WS18G    WS95B    WS99B    WS98G    WS96G    WS97G
    The pushbutton non-retractable lap belts listed below are available in 60",74",and 90" overall length and match the late model retractable seat belts listed above and can be used in the center or rear seat positions.All the plastic pieces are color matched to the webbing color except for the red belts where these pieces are black.Requires one WSMH2 bolt kit per belt.


    Description                              Cost 
60" Lap Belt                          $18.00ea
74" Lap Belt                          $19.00ea
90" Lap Belt                          $21.00ea
WSMH2 Bolt Kit                         $2.50ea
WSRB2 L-Bracket                        $2.50ea
WSRB1 Underbody Reinforcement Plate   $25.00pr

    
Color                       60"         74"         90"
Black                      WS01B       WS00B       WS20B
Medium Blue                WS01C       WS00C       WS20C
Burgundy/Maroon            WS01D       WS00D       WS20D
Medium Gray                WS01E       WS00E       WS20E
Tan                        WS01F       WS00F       WS20F
Bright Red                 WS01G       WS00G       WS20G
    Return To Seat Belt Main Index Page



    All information detailed within this document is based on information believed to be accurate but accuracy is not guaranteed.All pictures,diagrams and item descriptions are protected property of The Andover Companies,Inc and are not to be duplicated in any manner without written permission.

    (late 11-15-04)