Cable Side Seat Belts With Closed Or Open Micro Safety Switch
Cable and bracket side end release buckle seat belts available with an open or closed micro circuit safety switch. All of the seat belts and related hardware are new and manufactured to meet or exceed FMVSS (U.S. Federal Motor Vehicle Safety Standards) 209,302 and SAE 386 with most manufactured or assembled in the USA.The available seat belt styles include non retractable and retractable lap only seat belts and retractable lap and shoulder harness with a cable or bracket buckle side in lengths from 5" to 13" long with webbing colors to match most interior colors.Webbing colors tend to vary from mill run to mill run therefore a match to upholstery or carpet can not be guaranteed.
Note:When installing a seat belt where it was not previously installed or if a factory underbody or shoulder harness reinforcement plates is damaged or missing it is suggested that a retrofit mounting kit be used which include underbody and or shoulder harness reinforcement plates to add support to the mounting points. Basic mounting kits are not required when purchasing a retrofit mounting kit.
Click Here for cable/bracket buckle side seat belts with out a micro safety switch.
THE DIFFERENCE BETWEEN A CLOSED AND OPEN CIRCUIT Closed Circuit: If wired to the ignition requires that the latch(male side) be inserted in to the buckle in order to complete the circuit which will allow the starting. If wired to a dash lamp the lamp will illuminate when the latch(male side) side is inserted in to the buckle indicating that the seat belt has been connected.
Open Circuit: If wired, it does not require that the latch(male side) be inserted in to the buckle to complete the circuit. If wired to a buzzer or to an alarm it will sound until the latch(male side) and the buckle are connected or if wired to a dash lamp the lamp will stay illuminated.
Non Retractable Lap Belt With Closed Circuit
Specifications:
Available in lengths of 60" and 74" with cable/bracket side lenghts of 5"(actual 5.25"), 7"(actual 7.25"), 9"(actual 9.75") and 13"(actual 13.25").
Buckle is an end release push button. Except for the red on the push button all the plastic pieces are black.
Has a 5 amp electrical rating.
One MH2 basic or 201K retrofit mounting kit is required per seat belt.MH2 basic kit not required when using a 201K retrofit kit.
Two RB6 L-brackets may be required based on the mounting location. Requires one additional MH2 for mounting.
To Order:
Call:(302) 629-8508 8-5 EST Monday-Friday
Or use the secure on-line order form located below.
Column Description Item Number Series
A 60" Long With A 5" Bracket Buckle Side W8260-5E
B 60" Long With A 7" Cable Buckle Side W8260-7E
C 60" Long With A 9" Cable Buckle Side W8260-9E
D 60" Long With A 13" Cable Buckle Side W8260-12E
E 74" Long With A 5" Bracket Buckle Side W8261-5E
F 74" Long with A 7" Cable Buckle Side W8261-7E
G 74" Long with A 9" Cable Buckle Side W8261-9E
H 74" Long With A 13" Cable Buckle Side W8261-12E
201K- Retrofit Mounting Kit.One Required Per Belt.
$11.00ea
RB6- L-Bracket. Two Required Per Seat Belt.Requires One Additional MH2 For Mounting.
$2.50ea
Retractable Lap Belt With Closed Or Open Circuit
Specifications;
The buckle is an end release push button.
The webbing when fully extending from the retractor measures 52" long.
The buckle side measures 9" long with a covered twisted steel cable with a rubberized protective coating.
Except for the red on the push button all of the plastic pieces are black.
Has a 5 amp electrical rating with 14" long wires with weather protected plug in end fitting.
The retractor is (ALR) automatic locking with protective boot. Must release back to the retractor to adjust length once locked in position.
One MH2 basic or 201K retrofit mounting kit is required per seat belt.MH2 kit is not required when using a 201K retrofit kit.
Two RB6 L-brackets may be required to mount retractor upright or to adjust location of buckle side.One additional MH2 mounting kit required.
To Order:
Call:(302) 629-8508 8-5 EST Monday-Friday
Or use the secure on-line order form located below.
Item Number Description
W8433B With Closed Circuit Micro Switch.Black Webbing
W8433J With Closed Circuit Micro Switch.Orange Webbing
W8434B With Open Circuit Micro Switch.Black Webbing
W8434J With Open Circuit Micro Switch.Orange Webbing
Retractable Lap Belt With Closed Or Open Circuit
Price
Select Color
Order
Closed Circuit Retractable Lap Belt With Cable Buckle Side-W8433 Series.
$46.50ea
Open Circuit Retractable Lap Belt With Cable Buckle Side-W8434 Series.
$45.00ea
RB6- 1 1/2" L-Bracket.One Additional MH2 Required Per Two Brackets.
$2.50ea
MH2- Basic Mounting Kit. One Kit Required Belt.
$2.50ea
201K- Retrofit Mounting Kit. One Kit Required Belt.
$2.50ea
Retractable Lap Belt With Closed Circuit And 4" Or 7" Retractor Boot
Specifications;
The webbing when fully extended from the retractor measures 52" long.
The buckle is an end release push button.Except for the red on the push button all of the plastic pieces are black.
Available buckle side lengths of 5"(actual 5.25"), 7"(actual 7.25"), 9"(actual 9.75") and 13"(actual 13.25").
Has a 5 amp electrical rating.
The retractor is (ALR)automatic locking. Must be released back to the retractor to extend length once locked in position.
The black retractor boot is available 4" or 7" long.
One 200 basic or 202K(Bucket Seats) or 204K(Bench Seats) retrofit mounting kit is required per seat belt.A 200 kit is not required when using a retrofit kit.
To Order:
Call:(302)629-8508 8-5 EST Monday-Friday
Or use the secure on-line order form located below.
Column Description Item Number Series
A with 4" Long Retractor Boot And A 5" Bracket Buckle Side W8258-5E
B with 4" Long Retractor Boot And A 7" Cable Buckle Side W8258-7E
C with 4" Long Retractor Boot And A 9" Cable Buckle Side W8258-9E
D With 4" Long Retractor Boot And A 13" Cable Buckle Side W8258-12E
E With 7" Long Retractor Boot And A 5" Bracket Buckle Side W8233-5E
F With 7" Long Retractor Boot And A 7" Cable Buckle Side W8233-7E
G With 7" Long Retractor Boot And A 9" Cable Buckle Side W8233-9E
H With 7" Long Retractor Boot And A 13" Cable Buckle Side W8233-12E
200- Basic Retractable Lap Seat Belt Mounting Kit.One Required Per Belt.
$4.75ea
202K- Bucket Seat Retrofit Mounting Kit.One Required Per Belt.
$16.25ea
204K- Bench Seat Retrofit Mounting Kit.One Required Per Belt.
$13.75ea
Retractable Lap Belt With Shoulder Harness With Closed Circuit
Specifications;
Available with webbing length extended from retractor of 85", 110" and 140" long.
Cable/Bracket buckle side available lengths of 5"(actual 5.25"), 7"(actual 7.25"), 9"(actual 9.75") and 13"(actual 13.25").
Buckle is a end release push button.Except for the red on the push button all of the plastic pieces are black.
Has a 5 amp electrical rating.
The retractor is (ELR) web sensitive emergency locking type which allows for some movement but locks based on a specific motion.
One 300 basic or 302K(Bucket Seats) or 303K(Bench Seats) retrofit mounting kit is required per seat belt.A 300 kit is not required when using a retrofit kit.
To Order:
Call:(302) 629-8508 8-5 EST Monday-Friday
Or use the secure on-line order form located below.
Column Description Item Number Series
A 85" Long With 5" Bracket Buckle Side W8236-5E
85" Long With 7" Cable Buckle Side W8236-7E
85" Long With 9" Cable Buckle Side W8236-9E
B 85" Long With 13" Cable Buckle Side W8236-12E
C 110" Long with 5" Bracket Buckle Side W8257-5E
110" Long With 7" Cable Buckle Side W8257-7E
110" Long With 9" Cable Buckle Side W8257-9E
D 110" Long With 13" Cable Buckle Side W8257-12E
E 140" Long With 5" Bracket Buckle Side W8262-5E
140" Long With 7" Cable Buckle Side W8262-7E
140" Long With 9" Cable Buckle Side W8262-9E
F 140" Long With 13" Cable Buckle Side W8262-12E
Retractable Lap Belt And Shoulder Harness With Closed Circuit
Price
Select Color
Order
Column A: 85" Long With 5" Bracket Buckle Side-W8236-5E Series.
$85.00ea
85" Long With 7" Long Cable Buckle Side-W8236-7E Series.
$85.00ea
85" Long With 9" Long Cable Buckle Side-W8236-9E Series.
$85.00ea
Column B: 85" Long With 13" Cable Buckle Side-W8236-12E Series.
$85.00ea
Column C: 110" Long With 5" Bracket Buckle Side-W8257-5E Series.
$85.00ea
110" Long With 7" Long Cable Buckle Side-W8257-7E Series.
$85.00ea
110" Long With 9" Long Cable Buckle Side-W8257-9E Series.
$85.00ea
Column D: 110" Long With 13" Cable Buckle Side-W8257-12E Series.
$85.00ea
Column E: 140" Long With 5" Bracket Buckle Side-W8262-5E Series.
$85.00ea
140" Long With 7" Long Cable Buckle Side-W8262-7E Series.
$85.00ea
140" Long With 9" Long Cable Buckle Side-W8262-9E Series.
$85.00ea
Column F: 140" Long With 13" Cable Buckle Side-W8262-12E Series.
$85.00ea
300- Basic Mounting Kit.Retractable lap With harness.One Required per Belt.
$5.25ea
303K- Bench Seat Retrofit Mounting Kit.Retractable Lap With Harness.One Required Per Belt.
$22.50ea
302K- Bucket Seat Retrofit Mounting Kit.Retractable Lap With Harness.One Required Per Belt.
$25.75ea
Reinforcement Plates
Price
Order
RB3- Shoulder Harness Reinforcement Plate With Weld Nut.Each.
$12.00ea
RB1-1- Underbody Reinforcement Plate With Weld Nut.Each.
$14.50ea
RB1- Underbody Reinforcement Plate With Weld Nut.Pair.
$25.00pr
Liability Disclaimer: The Andover Companies, and its subsidiaries assumes no responsibility for any damage due to the installation, either proper or improper, or for any damage or bodily injury arising from the use of any product. It is understood that the purchaser, installer and/or end user is responsible for the determination that the product purchased is suitable for its intended use and agrees to indemnify and hold The Andover Companies,Inc and its subsidiaries, harmless for any claim, action or demand arising from the installation and/or use of any product. There are no guarantees or warrantees on any product, implied or expressed, of fitness for a particular use with any such warrantees being specifically and expressly disclaimed. In the event any of the above limitations are held not enforceable our liability shall not exceed an amount equal to the amount paid to us for the product. Receipt of product or products confirm acceptance of disclaimer and liability transfer to purchaser, installer and/or end user.
All information detailed within this document is based on information believed to be accurate but accuracy is not guaranteed. All pictures, diagrams and item descriptions are protected property of The Andover Companies,Inc and are not to be duplicated in any manner without written permission.