Main Index With Open Safety Switch Without Safety Switch Components And Hardware
Contact Us-EMail Call Us:(302)629-8508

End release cable and bracket buckle seat belts with a closed circuit micro safety available as a non retractable lap seat belt,retractable lap seat belt, non retractable lap seat belt with shoulder harness and retractable lap seat belt with an attached shoulder harness.

.....Closed Circuit Description
  • To function as designed the buckle end wires must wired directly or the end connector must be plugged in to an alarm buzzer or illuminated light circuit.
  • In its operational state, the seat belt latch end and the buckle end do not need to be connected in order for the engine to start.
  • A dash alarm will sound or a dash light will illuminate until the seat belt latch end is connected in to the seat belt buckle turning off the micro safety switch.
  • If the seat belt latch end is removed from the seat belt buckle when the engine is running the engine will not shut off. The alarm will sound or the dash light will illuminate indicating the seat belt latch is no longer connected in to the seat belt buckle.
    Application Examples
  • Used in many newer vehicles to indicate that the seat belt is not being worn.
  • To have a alarm buzzer sound to indicate that the seat belt latch end is not connected to the seat belt buckle or has been disconnected.
  • To have an indicator light illuminate to indicating that the seat belt is not being worn.

    The seat belts listed are an aftermarket universal fit and are not implied to be vehicle or application specific. No guarantee is made as to fit or if a component or webbing color will match an existing seat belt or interior color.All seat belts and related hardware are new and manufactured to meet or exceed FMVSS (U.S. Federal Motor Vehicle Safety Standards) 209 and 302 with all of the seat belts manufactured or assembled in the USA.

    Non Retractable



    Lap Seat Belt With Wired 7" Bracket Buckle

    Quantity

    Add MH2-YZ Mounting Kit $3.25ea
    Add 201K-Z Retrofit Mounting Kit $12.00ea
    Add CR1 Plastic Clip-On Retractor $9.50ea
    Add 80296 Chrome "Roll-A-Belt" Clip-On Retractor $20.00ea

    Product Notes: Click On Pictures To Enlarge
  • Available with all webbing colors on sample page.
  • Click Here To View Webbing Colors Or To Order Samples
  • Contact us for the availability of wired 9" and 12" long buckles with cable ends.
  • All plastic pieces except buckle press area are black.
  • For matching buckle center seat belt see center non retractable lap seat belt.
  • Retrofit kit includes underbody reinforcements and should be used when seat belts were not previously installed.When purchasing a retrofit kit a MH2-YZ mounting kit is not required.
  • See mounting brackets at the end of section for buckle side mounting or specialty installations.
    For product questions or ordering assistance call (302)629-8508

  • Lap Seat Belt With Shoulder Harness With 7" Wired Bracket Buckle

    Quantity

    Add MH9 Mounting Kit $4.75ea
    Add 301K-Z Retrofit Mounting Kit $21.50ea

    Product Notes: Click On Pictures To Enlarge
  • Available with all webbing colors on sample page.
  • Click Here To View Webbing Colors Or To Order Samples
  • Contact us for the availability of wired 9" and 12" long buckles with cable ends.
  • All plastic pieces except buckle press area are black.
  • For matching buckle center seat belt see center non retractable lap seat belt.
  • Retrofit kit includes underbody reinforcements and should be used when seat belts were not previously installed. When purchasing a retrofit kit a MH9 mounting kit is not required.
  • See mounting brackets at the end of section for buckle side mounting or specialty installations.
    For product questions or ordering assistance call (302)629-8508
  • Center And Rear Seat Lap Seat Belt

    Quantity

    Add MH2-YZ Mounting Kit $3.25ea

    Product Notes:Click On Picture To Enlarge
  • Available with all webbing colors on sample page.
  • Click Here To View Available Webbing Colors Or To Order Samples
  • Use on center seat position when cable/bracket seat belts are installed at the outer positions.
  • Use on all rear seat position when cable/bracket seat belts are installed in the front.
  • Does not include micro safety switch.
  • All plastic pieces except buckle press area are black.
  • Mounting kit is not required when installing in a center position.
  • A MH2-YZ mounting is required when installing in outer positions.
    For product questions or ordering assistance call (302)629-8508
  • Retractable Lap Seat Belt:Industrial Use


    Retractable Lap

    Quantity

    Add MH2-YZ Mounting Kit $3.25ea
    Add 200K Mounting Kit With L-Bracket $4.75ea

    Click On Picture To Enlarge
  • W8434-1 buckle should be used with W8434 series seat belts only.
  • Available with black or safety orange webbing.
  • The buckle side is 9" long with a 1/2" mounting hole.
  • Has 5amp two wire plug in weather protected connector.
  • The retractor is (ALR) automatic locking with a hard plastic protective boot that measures 4" wide x 2 1/2" tall x 3 3/4" wide.
  • The webbing when fully extended from the retractor measures 52" long.
  • All of the plastic pieces except for the buckle end press are black.
  • MH2-YZ mounting kit should be used when attaching flat to the side of a seat.
  • 200K mounting kit should be used when attaching the retractor upright to the floor to the side of a seat.
  • Specialty brackets and extensions are listed at end of section to adjust the mounting position or location.
  • Lengths listed are approximate.
    For product questions or ordering assistance call (302)629-8508


  • Retractable Lap Seat Belts

    General Information
  • The seat belts listed can be used for driver or passenger side installation.
  • All of the seat belts, components, mounting kits and hardware are priced and sold each/per person.
  • The retractor is automatic locking(ALR) which locks when the webbing has been pulled and released at the desired location.
  • To adjust the extended length once the retractor has locked the webbing must be released back to the retractor and re-pulled.

    Mounting Hardware
  • Always use factory mounting points when possible.
  • A retrofit mounting kit should be used if the location where the seat belt is being installed did not have a seat belt previously factory installed.
  • Retrofit mounting kits include underbody reinforcement plates to add support to mounting points, L-bracket(s) to mount the retractor upright and mounting hardware.
  • If a retrofit mounting kit is purchased a 200K mounting kit is not required.
  • An additional L-bracket may be required based on the selected mounting position and location of the retractor or buckle side. See mounting brackets at the end of page.
  • For suggestions regarding the creation or reinforcement of mounting points refer to the Help Page.


    Retractable Lap With Wired 7" Bracket Buckle

    Quantity

    Add 200K Mounting Kit With L-Bracket $4.75ea
    Add 202K Retrofit Mounting Kit.Bucket Seat $16.25ea
    Add 204K Retrofit Mounting Kit.Bench Seat $13.75ea

    Product Notes: Click On Pictures To Enlarge
  • Available with all webbing colors on sample page.
  • Click Here To View Webbing Colors Or To Order Samples.
  • Contact us for the availability with a 4" boot and wired 9" and 12" long buckles with cable ends.
  • All plastic pieces except buckle press area are black.
  • For matching buckle center seat belt see center non retractable lap seat belt.
  • Retrofit kits includes underbody reinforcements and should be used when seat belts were not previously installed.When purchasing a retrofit kit a 200K mounting kit is not required.
  • See mounting brackets at the end of section for buckle side mounting or specialty installations.
    For product questions or ordering assistance call (302)629-8508
  • Retractable Lap Belt With Shoulder Harness Seat Belts

    General Information
  • The seat belts listed can be used for a drivers or passenger side installation.
  • All of the seat belts,components,mounting kits and hardware are priced and sold each/per person.
  • The retractor is emergency locking(ELR) with a web sensitive inertia reel that locks instantly on sudden webbing movement.

    Shoulder Harness Configuration And Extended Lengths Selection
  • For assistance determining extended length, door post type or the creation of a shoulder harness mounting point refer to Help Page.

    Mounting Hardware Selection
  • Always use the factory mounting locations when possible.
  • A retrofit mounting kit should be used if the location where the seat belt is being installed did not have a seat belt previously factory installed.
  • Retrofit kits include shoulder harness and underbody reinforcement plates to add additional support to the mounting points, L-bracket(s) to mount the retractor upright and mounting hardware
  • When a retrofit mounting kit is purchased a 300K mounting kit is not required.
  • Some installations may require additional L-brackets or specialty brackets based on the mounting location of the retractor or buckle end. See mounting brackets at the end of the page.
  • For suggestions regarding the creation or reinforcement of mounting points refer to the Help Page.





    Without Door Post Extension(DPE) With Wired 7" Bracket Buckle

    Quantity

    Add 300K Mounting Kit With L-Bracket $5.25ea
    Add 206K Retrofit Mounting Kit $21.75ea

    Add ADJ3B Black Stop Button (Not Installed) $2.50ea
    Add ADJ3G Grey Stop Button (Not Installed) $2.50ea
    Add ADJ3T Tan Stop Button (Not Installed) $2.50ea
    Add BZ-1B Deck Or Trim Panel Bezel.Black. $10.00ea
    Add BZ-1T Deck Or Trim Panel Bezel.Tan. $10.00ea

    Product Notes: Click On Pictures To Enlarge
  • A web stop button keeps the latch from sliding down the webbing when the seat belt is not in use.
  • Available with all webbing colors on sample page.
  • Click Here To View Webbing Colors Or To Order Samples.
  • Contact us for the availability of 9" and 12" long buckles with cable ends.
  • All plastic pieces except buckle press area are black.
  • For matching buckle center seat belt see center non retractable lap seat belt.
  • Retrofit kit includes underbody reinforcements and should be used when seat belts were not previously installed.When purchasing a retrofit kit a 300K mounting kit is not required.
  • See mounting brackets at the end of seaction for buckle side mounting or specialty installations.
    For product questions or ordering assistance call (302)629-8508




  • With 2 1/2" Door Post Extension(DPE) With Wired 7" Bracket Buckle

    Quantity

    Add 300K Mounting Kit With L-Bracket $5.25ea
    Add 302K Retrofit Mounting Kit.Bucket Seat $25.75ea
    Add 303K Retrofit Mounting Kit.Bench Seat $22.50ea

    Add ADJ3B Black Stop Button(Not Installed) $2.50ea
    Add ADJ3G Grey Stop Button(Not Installed) $2.50ea
    Add ADJ3T Tan Stop Button(Not Installed) $2.50ea
    Add BZ-1B Deck Or Trim Panel Bezel.Black. $10.00ea
    Add BZ-1T Deck Or Trim Panel Bezel.Tan. $10.00ea

    Product Notes: Click On Pictures To Enlarge
  • A web stop button keeps the latch from sliding down the webbing when the seat belt is not in use.
  • Available with all webbing colors on sample page.
  • Click Here To View Webbing Colors Or To Order Webbing Samples.
  • Contact us for the availability of wired 9" or 12" long buckles with cable ends.
  • All plastic pieces except buckle press area are black.
  • For matching buckle center seat belt see center non retractable lap seat belt.
  • Retrofit kit includes underboy and shoulder harness reinforcing plates and should be used when seat belts were not previously installed. When purchasing a retrofit kit a 300K mounting kit is not required.
  • See mounting brackets at the end of section for buckle side mounting or specialty installations.
    For product questions or ordering assistance call (302)629-8508




  • With 8" Door Post Extension(DPE) With Wired 7" bracket Buckle

    Quantity

    Add 300K Mounting Kit With L-Bracket $5.25ea
    Add 302K Retrofit Mounting Kit.Bucket Seat $25.75ea
    Add 303K Retrofit Mounting Kit. Bench Seat $22.50ea

    Add ADJ3B Black Stop Button(Not Installed) $2.50ea
    Add ADJ3G Grey Stop Button(Not Installed) $2.50ea
    Add ADJ3T Tan Stop Button(Not Installed) $2.50ea
    Add BZ-1B Deck Or Trim Panel Bezel.Black.$10.00ea
    Add BZ-1T Deck Or Trim Panel Bezel.Tan. $10.00ea

    Product Notes: Click On Pictures To Enlarge
  • A web stop button keeps the latch from sliding down the webbing when the seat belt is not in use.
  • Available with all webbing colors on sample page.
  • Click Here To View Webbing Colors Or To Order Webbing Samples.
  • Contact us for the availability of wired 9" or 12" long buckles with cable ends.
  • All plastic pieces except buckle press area are black.
  • For matching buckle center seat belt see center non retractable lap seat belt.
  • Retrofit kit includes underboy and shoulder harness reinforcing plates and should be used when seat belts were not previously installed. When purchasing a retrofit kit a 300K mounting kit is not required.
  • See mounting brackets at the end of section for buckle side mounting or specialty installations.
    For product questions or ordering assistance call (302)629-8508


  • Specialty Mounting Brackets

    Quantity:

    Add MH2-YZ Mounting Kit. $3.25ea

    Product Notes:
  • Click On Picture To Enlarge
  • RB6: 1 1/2" long L-bracket.Yellow zinc.
  • RB2: 2" long L-bracket.Yellow zinc.
  • RB9: 5" long double angle bracket.Yellow zinc.
  • RB8: 7" long single angle bracket.Yellow zinc.
  • RB7: 3" long flat extension.Yellow zinc.
  • RB11: 6" long flat extension.Yellow zinc.
  • RB10: 12" long single angle bracket.Yellow zinc.
    For product questions or ordering assistance call (302)629-8508.


  • Reinforcement Plates

    Quantity:

    Add MH11 Zinc Chromate Mounting Bolt $1.30ea. Order One per Plate
    Add MH12 Zinc Chromate Lock Washer $.35ea. Order One Per Plate

    Product Notes:
  • Click On Picture To Enlarge
  • RB1-1: Curved steel with attached nut.Measures 4 1/2" x 3".
  • RB1: Same as RB1-1 except pair.
  • RB3: Steel with attached nut. Measures 4 1/2"(not including tip) x 1 1/2".
  • RB4: Measures 3" x 1 1/2" and accepts a 7/16th fine thread bolt.
    For product questions or ordering assistance call (302)629-8508.

  • Liability Disclaimer: The Andover Companies, and its subsidiaries assumes no responsibility for any damage due to the installation, either proper or improper, or for any damage or bodily injury arising from the use of any product. It is understood that the purchaser, installer and/or end user is responsible for the determination that the product purchased is suitable for its intended use and agrees to indemnify and hold The Andover Companies,Inc and its subsidiaries, harmless for any claim, action or demand arising from the installation and/or use of any product. There are no guarantees or warrantees on any product, implied or expressed, of fitness for a particular use with any such warrantees being specifically and expressly disclaimed. In the event any of the above limitations are held not enforceable our liability shall not exceed an amount equal to the amount paid to us for the product. Receipt of product or products confirm acceptance of disclaimer and liability transfer to purchaser, installer and/or end user.

    All information detailed within this document is based on information believed to be accurate but accuracy is not guaranteed. All pictures, diagrams and item descriptions are protected property of The Andover Companies,Inc and are not to be duplicated in any manner without written permission.

    (cable1-closed 10-2-15)