Cable or bracket buckle side seat belts that are available non retractable or retractable, with or with out a shoulder harness with webbing colors to match most interiors for most makes and models of American and imported automobiles and trucks. All seat belts and related hardware are new and manufactured to meet or exceed FMVSS (U.S. Federal Motor Vehicle Safety Standards) 209,302 and SAE 386 with most manufactured or assembled in the USA.
The seat belts listed are an aftermarket universal fit and are not implied to be vehicle or application specific. No guarantee is made as to fit or if a webbing color will match an existing seat belt or interior color. Click Here for a vehicle specific seat belt, seat belts for non-automotive and seatbelts for specialty applications.
|
Lap Seat Belt-Non-Retractable
|
Retractable Lap Seat Belt Choices
General Information
The seat belts listed can be used for a driver or passenger side installation.
All of the seat belts,components,mounting kits and hardware are priced and sold each/per person.
The retractor is automatic locking(ALR) which locks when the webbing has been pulled and released at the desired length.
To adjust the extended length once the retractor has locked in position the webbing must be released back to the retractor first.
The seat belts listed are universal fit without electrical wiring and are not guaranteed to fit all applications.
Webbing colors,colored boots and colored components are not guaranteed to match existing webbing, components or interior color.
All lengths and measurements listed are approximate.
The invoice may show a different product part numer.
Boot Length Selection
A 7" long retractor boot raises the height of the latch.Depending of the seat height from the floor may make it easier to reach.
The 4" long retractor boot is what most installation will require.
Mounting Hardware Selection
Always use the factory mounting locations when possible.
It is suggested that a retrofit mounting kit be used if the location where the seat belts are being installed did not have seat belts previously factory installed. Retrofit kits include underbody reinforcement plates to add additional support to the mounting locations,retractor L-brackets to mount the retractor upright and attachment hardware.
If a retrofit mounting kit is purchased the basic mounting kit is not required.
An additional L-bracket may be required based on the selected mounting position and location of the buckle end side.
If the vehicle was not factory equiped with seat belts Click Here to see how to add attachement locations.
|
Retractable Lap Belt With 4" Retractor Boot
|
Retractable Lap And Shoulder Harness Seat Belt Choices
General Information
The seat belts listed can be used for a drivers or passenger side installation.
All of the seat belts,components,mounting kits and hardware are priced and sold each/per person.
The retractor is emergency locking(ELR) with a web sensitive inertia reel that locks instantly on sudden webbing movement.
The seat belts listed are universal fit without electrical wiring and are not guaranteed to fit all applications.
Webbing colors,colored boots and colored components are not guaranteed to match existing webbing, components or interior color.
All lengths and measurements listed are approximate.
The invoice may have a different product part number.
Shoulder Harness Mounting Configuration Selection
A shoulder harness seat belt without a door post extension is used in a convertible or when the retractor is mounted below the window.
The selection of a 2 1/2" or a 8 1/2" door post extension in a matter of preference.The 8 1/2" door post extension will lower the webbing path where it comes across the neck.
Length Selection
110"long is the most common fully extended length when the seat belt being installed has a 2 1/2" door post extension and the harness mounting bracket is located below the window.
140"long is the most common fully extended length when the seat belt being installed has a 2 1/2" or 8 1/2" door post extension and the harness mounting bracket is located on the roof or above the window on a door post.
..........Available Fully Extended Lengths.Lengths listed are approximate.
85" Long: 5" of webbing remains outside of the retractor when fully retracted.
110" Long: 30" of webbing remains outside of the retractor when fully retracted.
125" Long: 45" of webbing remains outside of the retractor when fully retracted.
140" Long: 60" of webbing remains outside of retractor when fully retracted.
Mounting Hardware Selection
Always use the factory mounting locations when possible.
It is suggested that a retrofit mounting kit be used if the location where the seat belts are being installed did not have seat belts previously factory installed. Retrofit kits include underbody and shoulder harness reinforcement plates to add additional support to the mounting locations,retractor L-brackets to mount the retractor upright and attachment hardware.
If a retrofit mounting kit is purchased the basic mounting kit is not required.
An additional L-bracket may be required based on the selected mounting position and location of the buckle end side.
If the vehicle was not factory equiped with a shoulder harness click Here to see how to retrofit the attachement point.
|
Retractable Lap Belt With Shoulder Harness
-Without Door Post Extension
|
|
Retractable Lap Belt With Shoulder Harness
-With 2 1/2" Door Post Extension
|
|
Retractable Lap Belt With Shoulder Harness
-With 8" Door Post Extension
|
 |
Mounting Brackets
|
 |
Reinforcement Plates
|
Liability Disclaimer: The Andover Companies, and its subsidiaries assumes no responsibility for any damage due to the installation, either proper or improper, or for any damage or bodily injury arising from the use of any product. It is understood that the purchaser, installer and/or end user is responsible for the determination that the product purchased is suitable for its intended use and agrees to indemnify and hold The Andover Companies,Inc and its subsidiaries, harmless for any claim, action or demand arising from the installation and/or use of any product. There are no guarantees or warrantees on any product, implied or expressed, of fitness for a particular use with any such warrantees being specifically and expressly disclaimed. In the event any of the above limitations are held not enforceable our liability shall not exceed an amount equal to the amount paid to us for the product. Receipt of product or products confirm acceptance of disclaimer and liability transfer to purchaser, installer and/or end user.
All information detailed within this document is based on information believed to be accurate but accuracy is not guaranteed. All pictures, diagrams and item descriptions are protected property of The Andover Companies,Inc and are not to be duplicated in any manner without written permission.
(cable 6-22-11)
|
