Seat Belt Main Index Page On Sale Contact Us:EMail
Hardware And Components Matching Non Retractable Belts More Buckle Choices
Push button buckle seat belts available as a non retractable lap seat belt, non retractable lap seat belt with shoulder harness, retractable lap seat belt and retractable lap seat belt with shoulder harness with webbing colors to match the original or aftermarket interiors of most makes and models of American and imported automobiles and trucks with "No Charge For Shipping" by ground within the CUSA, lower 48. All of seat belts and related hardware are new and manufactured to meet or exceed FMVSS (U.S. Federal Motor Vehicle Safety Standards) 209 and 302 with all of the seat belts manufactured or assembled in the USA.

The seat belts are an aftermarket universal fit and are not implied to be vehicle or application specific. No guarantee is made as to fit or if a component or webbing color will match an existing seat belt or interior color. Click Here for vehicle specific seat belts, non automotive seat belts and seatbelts for specialty applications. You will be re-directed to the main index page of Andover Restraints, also a division of The Andover Companies. No charge shipping does not apply to purchases from the Andover Restraints site.

Retractable Lap Seat Belts

General Information
  • The seat belts listed can be used for driver or passenger side installation.
  • Seat belt warning or any dash electrical connectors are not included.
  • All of the seat belts, components, mounting kits and hardware are priced and sold each/per person.
  • The retractor is automatic locking(ALR) which locks when the webbing has been pulled and released.
  • To adjust the length once the retractor has locked the webbing must be released back to the retractor and re-pulled.

    Buckle Ends Selection
  • A buckle side with a plastic sleeve in most cases is used in a vehicle with bucket seats.
  • A buckle side without a plastic sleeve in most cases is used in a vehicle with bench seats.

    Boot Length Selection
  • Most installations will use a 4" long retractor boot.
  • If the seat is raised, a 7" long boot will increase the height of the latch end making it easier to reach.

    Mounting Hardware
  • Always use factory mounting points when possible.
  • Retrofit mounting kits should be used if the location seat belts are to be installed did not previously have seat belts factory installed.
  • Retrofit mounting kits include underbody reinforcement plates to add support to the mounting points, L-bracket(s) to mount the retractor upright and mounting hardware.
  • When a retrofit mounting kit is purchased a basic or standard mounting kit is not required.
  • An additional L-bracket may be required based on the mounting position or location of the retractor or buckle side. See mounting brackets at the end of section.
  • For suggestions regarding the creation or reinforcement of the mounting points refer to the Help Page.



    Lap Belt With 4" Retractor Boot

    Quantity

    Click Here To View Webbing Colors

    Add 200K Mounting $4.25ea
    Add RB6 L-Bracket For Buckle Side $2.50ea
    Add MH8 Mounting Kit For Buckle Side RB6 L-Bracket $1.25ea
    Add 202K Retrofit Mounting Kit For Bucket Seats $16.25ea
    Add 204K Retrofit Mounting Kit For Bench Seats $13.75ea


    Product Notes: Click On Picture To Enlarge
  • All plastic pieces are color matched to the webbing except on the orange and red belts.
  • All plastic pieces on the orange and red seat belts are black.
  • The webbing fully extended from retractor measures 52" Long.
  • 200K mounting kit includes bolts, washers, nuts, reinforcing washers and L-bracket.
  • 202K or 204K retrofit kits should be used when seat belts were not previously installed.
  • Retrofit kits include underbody reinforcement plates, L-bracket(s) and mounting hardware.
  • 200K mounting kit is not required when purchasing a retrofit kit.
  • The color of the webbing under a buckle sleeve will vary in color.
  • Lengths listed are approximate.
  • Click Here For Matching Non Retractable Seat Belts
  • Retractable Lap And Shoulder Harness Seat Belts

    General Information
  • The seat belts listed can be used for a drivers or passenger side installation.
  • All of the seat belts, components, mounting kits and hardware are priced and sold each/per person.
  • The retractor is emergency locking(ELR) with a web sensitive inertia reel that locks instantly on sudden webbing movement.
  • The seat belts listed are universal fit without electrical wiring and are not guaranteed to fit all applications.

    Buckle End Selection
  • A buckle side with a plastic sleeve in most cases is used in a vehicle with bucket seats.
  • A buckle side without a plastic sleeve in most cases is used in a vehicle with bench seats.

    Shoulder Harness Configuration And Extended Lengths Selection
  • For assistance determining the extended length, door post extension type and or the creation of a shoulder harness mounting point refer to Help Page.

    Mounting Hardware
  • Always use factory mounting points when possible.
  • Retrofit mounting kits should be used if the location seat belts are to be installed did not previously have seat belts factory installed.
  • Retrofit mounting kits include underbody reinforcement plates to add support to the mounting points, L-bracket(s) to mount the retractor upright and mounting hardware.
  • When a retrofit mounting kit is purchased a basic or standard mounting kit is not required.
  • An additional L-bracket may be required based on the mounting position or location of the retractor or buckle side. See mounting brackets at the end of section.
  • For suggestions regarding the creation or reinforcement of the mounting points refer to the Help Page.






    Lap Belt With Shoulder Harness
    -With Out Door Post Extension-

    Quantity

    Click Here To View Webbing Colors

    Add 200K Mounting Kit $4.25ea
    Add RB6 L-Bracket For Buckle Side $2.50ea
    Add MH8 Mounting Kit For Buckle Side RB6 L-Bracket $1.25ea
    Add 206K Retrofit Mounting Kit $21.75ea

    Add ADJ3B Black Stop Button(Not Installed) $2.50ea
    Add ADJ3G Grey Stop Button (Not Installed) $2.50ea
    Add ADJ3T Tan Stop Button (Not Installed) $2.50ea
    Add BZ1-1B Black Deck Or Trim Panel Bezel $10.00ea
    Add BZ1-1T Tan Deck Or Trim Panel Bezel $10.00ea


    Product Notes: Click On Picture To Enlarge
  • All retractor covers are black.
  • The buckle, buckle cover and all plastic pieces on the orange and red seat belts are black.
  • The color of the webbing under the buckle sleeve will vary in color.
  • Design and length of shoulder harness webbing end floor fitting will vary.
  • The webbing fully extended from retractor measures 126" long.
  • When fully retracted 36" of webbing will remain outside of the retractor.
  • 206K retrofit should be used when seat belts were not previously installed.
  • Retrofit kits include shoulder harness and underbody reinforcement plates, L-bracket and hardware.
  • 200K mounting kit is not required when purchasing a retrofit kit.
  • A stop button keeps the latch from sliding down the webbing when seat belt is not in use.
  • Lengths listed are approximate.
  • Click Here For Matching Non Retractable Seat Belts





  • Lap Belt With Shoulder Harness
    -With 2" Door Post Extension-

    Quantity

    Click Here To View Webbing Colors

    Add 300K Mounting Kit $5.25ea
    Add RB6 L-Bracket For Buckle Side $2.50ea
    Add MH8 Mounting Kit For Buckle Side RB6 L-Bracket $1.25ea
    Add 302K Retrofit Mounting Kit For Bucket Seats $25.75ea
    Add 303K Retrofit Mounting Kit For Bench Seats $22.50ea

    Add ADJ3B Black Stop Button (Not Installed) $2.50ea
    Add ADJ3G Grey Stop Button (Not Installed) $2.50ea
    Add ADJ3T Tan Stop Button (Not Installed) $2.50ea
    Add BZ1-1B Black Deck Or Trim Panel Bezel $10.00ea
    Add BZ1-1T Tan Deck Or Trim Panel Bezel $10.00ea


    Product Notes: Click On Picture To Enlarge
  • All retractor covers are black.
  • The buckle, buckle cover and all plastic pieces on the orange and red seat belts are black.
  • The color of the webbing under the buckle sleeve will vary in color.
  • Design and length of shoulder harness webbing end floor fitting will vary.
  • The webbing fully extended from the retractor measures 140" long.
  • When fully retracted 46" of webbing remains outside of the retractor.
  • 302K or 303K retrofit kit should be used when seat belts were not previously installed.
  • Retrofit kits include shoulder harness and underbody reinforcement plates, L-bracket(s) and hardware.
  • 300K mounting kit is not required when purchasing a retrofit kit.
  • A stop button keeps the latch from sliding down the webbing when seat belt is not in use.
  • Lengths listed are approximate.
  • Click here For Matching Non Retractable Seat Belts





  • Lap Belt With Shoulder Harness
    -With 8" Door Post Extension-

    Quantity

    Click Here To View Webbing Colors

    Add 300K Mounting Kit $5.25ea
    Add RB6 L-Bracket For Buckle Side $2.50ea
    Add MH8 Mounting Kit For Buckle Side RB6 L-Bracket $1.25ea
    Add 302K Retrofit Mounting Kit For Bucket Seats $25.75ea
    Add 303K Retrofit Mounting Kit For Bench Seats $22.50ea

    Add ADJ3B Black Stop Button (Not Installed) $2.50ea
    Add ADJ3G Grey Stop Button (Not Installed) $2.50ea
    Add ADJ3T Tan Stop Button (Not Installed) $2.50ea
    Add BZ1-1B Black Deck Or Trim Panel Bezel $10.00ea
    Add BZ1-1T Tan Deck Or Trim Panel Bezel $10.00ea


    Product Notes: Click On Picture To Enlarge
  • All retractor covers are black.
  • The buckle, buckle cover and all plastic pieces on the orange and red seat belts are black.
  • The color of the webbing under the buckle sleeve will vary in color.
  • Design and length of shoulder harness webbing end floor fitting will vary.
  • The webbing fully extended from the retractor measures 140" long.
  • When fully retracted 46" of webbing remains outside of the retractor.
  • 302K or 303K retrofit kits should be used when seat belts were not previously installed.
  • Retrofit kits include shoulder harness and underbody reinforcement plates,L-bracket(s) and hardware.
  • 300K mounting kit is not required when purchasing a retrofit kit.
  • A stop button keeps the latch from sliding down the webbing when seat belt is not in use.
  • Lengths listed are approximate.
  • Click here For Matching Non Retractable Seat Belts



  • Mounting Brackets

    Quantity:
    Add MH2 Mounting Kit. $2.50ea


    Product Notes: Click On Picture To Enlarge
  • RB6: 1 1/2" long L-bracket. Yellow zinc.
  • RB2: 2" long L-bracket. Yellow zinc.
  • RB9: 5" long double angle bracket. Yellow zinc.
  • RB8-L: 7" long left angle bracket. 65 degree bend.
  • RB8-R: 7" long right angle bracket. 65 degree bend.
  • RB7: 3" long flat extension. Yellow zinc.
  • RB11: 6" long flat extension. Yellow zinc.
  • RB10: 12" long single angle bracket. Yellow zinc.
  • Lengths listed are approximate.

  • Reinforcement Plates

    Quantity:
    Add MH11 Zinc Chromate Mounting Bolt $1.30ea
    Add MH12 Zinc Chromate Lock Washer $.35ea


    Product Notes: Click On Picture To Enlarge
  • RB1-1: Curved steel with attached weldnut. Measures 4 1/2" x 3".
  • RB1: Same as RB1-1 except pair.
  • RB3: Steel with attached weldnut. Measures 4 1/2"(not including tip) x 1 1/2".
  • RB4: Measures 3" x 1 1/2". Accepts a 7/16th fine thread bolt.
  • Lengths listed are approximate.

  • Liability Disclaimer: The Andover Companies, and its subsidiaries assumes no responsibility for any damage due to the installation, either proper or improper, or for any damage or bodily injury arising from the use of any product. It is understood that the purchaser, installer and/or end user is responsible for the determination that the product purchased is suitable for its intended use and agrees to indemnify and hold The Andover Companies,Inc and its subsidiaries, harmless for any claim, action or demand arising from the installation and/or use of any product. There are no guarantees or warrantees on any product, implied or expressed, of fitness for a particular use with any such warrantees being specifically and expressly disclaimed. In the event any of the above limitations are held not enforceable our liability shall not exceed an amount equal to the amount paid to us for the product. Receipt of product or products confirm acceptance of disclaimer and liability transfer to purchaser, installer and/or end user.

    All information detailed within this document is based on information believed to be accurate but accuracy is not guaranteed. All pictures, diagrams and item descriptions are protected property of The Andover Companies,Inc and are not to be duplicated in any manner without written permission.

    (SBL8-1 11-2-13)